Aluminum recycling has become a successful business since its inception a century ago. Nearly a third of the aluminum produced in the United States is made from aluminum scraps that have been recycled in a process—usually remelting—that uses only 5 to 10 percent of the energy it takes to extract aluminum from mined bauxite ore.
But there are limitations to the remelting of aluminum, says Wojciech Misiolek, the director of Lehigh’s Institute for Metal Forming and the Loewy Chair in Materials Forming and Processing.
Significant metal losses can occur when aluminum is remelted. Machine chips and other fine pieces of scrap are difficult to remelt. Contamination and impurities can cause the mechanical properties of recycled aluminum, especially its strength and ductility, to be inferior to those of pure aluminum. And remelting itself is energy-intensive.
In an effort to make aluminum production more sustainable, materials scientists are investigating solid state recycling of aluminum chips by extrusion, which promises higher metal yield, and lower heat use and energy consumption, than conventional recycling based on remelting.
A group that includes researchers from Lehigh and the Technical University (TU) of Dortmund in Germany has found that using special extrusion dies improves the mechanical properties of recycled aluminum by allowing more strain and shearing during metal flow.
Using transmission electron microscopy (TEM), the group is comparing the evolution of the microstructure, including the size and distribution of critical grain boundaries, of aluminum that is extruded through three different types of dies.
In the past year, the group has reported its results twice in Materials Science and Engineering A and once in the CIRP Annals of Manufacturing Technology.
In its experiments, the group processed machined aluminum chips into a cylindrically shaped billet and extruded the billet, pushing it through a die.
As aluminum flows through a die, it changes in shape and size. Shearing occurs as the rate of flow increases and decreases, causing the fracture of an oxide layer, which covers each chip and can act as a barrier that prevents bonding.
The researchers’ goal is to learn the amounts of shearing and deformation that promote optimal bonding between the aluminum chips. They hope to do this by guiding the development of the aluminum’s microstructure through the controlled fracture and dispersion of the oxide.
“We are trying to understand the critical conditions necessary to guarantee the good bonding of chips,” says Misiolek. “Our goal is to control the microstructure and improve the mechanical properties of the aluminum.”
While a continuous oxide layer can impede material bonding, says Misiolek, the researchers have learned that the right amount of the fractured oxide particles can result in a new and promising microstructure.
“TEM allows us to determine what shearing conditions are necessary to break the oxide layer and simultaneously preserve it to such an extent that it acts as a barrier to the growth of grain boundaries.
“We want to find this ‘sweet spot’ in shearing. We’re hoping this will enable us to control the mechanical properties of aluminum, especially its strength and ductility.”
The TU Dortmund researchers experimented with a conventional flat-face die used in the production of solid aluminum profiles, a porthole die used mostly to make complex hollow and semi-hollow profiles, and an ECAP (Equal Channel Angular Pressing) die, which guarantees the highest level of shear deformation and, therefore, modification of the microstructure.
While the aluminum extruded through the porthole dies possessed 80 percent more ductility than the aluminum extruded through the flat-face die, the researchers said, “the use of the ECAP die led to the highest strength and ductility of chipbased extrudates for the three dies.”
“With TEM, we can see grains, dislocations and other defects in the microstructure,” said Watanabe. “We were able to confirm that even at a lower temperature, severe plastic deformation [caused by the extrusion] changed the microstructure significantly, creating nanosized grains that improved the mechanical properties.”
In 2011-12, Misiolek spent six months at TU Dortmund’s Institute for Metal Forming and Light Construction as Mercator Visiting Professor. His stay was funded by the German Research Foundation. Last year, Matthias Haase of TU Dortmund spent two months as a visiting researcher at Lehigh.
Other collaborators are Ph.D. candidates Volkan Güley and Ahmet Güzel, and Dr. Andreas Jäger, Dr. Nooman Ben Khalifa, Prof. Matthias Kleiner and Prof. A. Erman Tekkaya, all of TU Dortmund; and Lehigh Ph.D. candidate Joseph C. Sabol.